HTB RAM Mapping 32×4 LCD Controller For I/o uc Features. Operating voltage: V~V Built-in kHz RC oscillator External kHz crystal or. Holtek HTB: available from 7 distributors. Explore Holtek on Octopart: the fastest source for datasheets, pricing, specs and availability. HT/HTG RAM Mapping 32´4 LCD Controller for I/O MCU PATENTED PAT No.: TW Features · Operating voltage: V~V · 32´4 LCD driver .
|Published (Last):||7 July 2013|
|PDF File Size:||16.30 Mb|
|ePub File Size:||18.41 Mb|
|Price:||Free* [*Free Regsitration Required]|
The LCD corresponding commands are summarized in the table.
Once the system is disabled or the tone output is inhibited, the BZ and the BZ outputs will remain at low level. The simulated RAM is used as a default.
Macduino: HT a seven segments LCD driver
The outputs of the time base generator and of the WDT time-out flag can be connected to the IRQ output by a h1t621b option. If the VDD drops below the minimum voltage of operating voltage spec. The following are the data mode IDs and the command mode ID: The CS line is used to initialize the serial interface circuit and to terminate the communication between the host controller and the HT Finally, a class for a specific 7-seg LCD module that I found at bargains.
The pins are connected as follows: An external KHz oscillator can also be used. Command The mode command should be issued before the data or command is transferred.
HTB (HOLTEK) PDF技术资料下载 HTB 供应信息 IC Datasheet 数据表 (4/20 页)
Memory structure of the HT The library consists in only one header and an implementation files: It is recommended that the host controller should read in the data from the DATA line datasheeg the rising edge of the RD line and the falling edge of the next RD line. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
Adtasheet both the time base generator and the WDT related commands, one should be careful since the time base generator and WDT share the same 8-stage counter. But if the external clock source is chosen as the system clock, using the SYS DIS command can neither turn the oscillator off nor carry out the power down mode.
Yes Yes Ht16221b Yes X: The serial interface circuit is also reset. The watch dog timer WDTon the other hand, is composed of an 8-stage time base generator along with a 2-stage count-up counter, and is designed to break the host controller or other subsystems from abnormal states such as unknown or unwanted jump, execution errors, etc.
As this information may be updated at regular intervals users are reminded to consult the Holtek website http: We have written a library to deal with all the features of HT But if CS is at logic low level and is input to the CS pad, the data and command transmission between the host controller and the HT are all enabled. These are stress ratings only.
Download the Holtek HT1621 LCD Controller Datasheet
The bold form of 1 0 0, namely 1 0 0, indicates the command mode ID. If the CS pin is set to 1, the data and command issued between the host controller and the HT are first disabled and then initialized. The configuration of the system oscillator is as h1t621b. The table illustrates the suggestion value of capacities C1, C2.
Calculation of the frequency is based on the system frequency sources as stated above. That is, after the external clock source is selected, the HT will continue working until system power fails or the external clock source is removed.
Of these, 1 0 0 indicates the command mode ID.
The crystal oscillator option can be applied to connect an external frequency source of 32kHz to the OSCI pin. We datashet that you can follow the table, which suggests the value of capacities.
The host controller can use the next rising edge to latch the clocked out data. Dimensions in mm Min. If successive commands have been issued, the command mode ID, namely 1 0 0, can be omitted. Holtek reserves the right to alter its products without prior notification.